Meter Box Upgrade Sydney: Costs, Signs and What’s Involved

asal electrical logo squareA.SAL Electrical Services
A.SAL Electrical van outside a Botany home during a meter box upgrade

A meter box upgrade replaces the enclosure that holds your electricity meter and main switch, along with the supply-side equipment connected to it. It often goes hand in hand with upgrading the switchboard, the mains cable and the earthing, so the whole setup meets current standards.

Signs your meter box needs an upgrade

Most meter boxes get upgraded for one of two reasons: something about the existing setup is no longer safe or compliant, or you’re adding something the current supply can’t handle.

The compliance signs are usually visible:

  • Porcelain fuses instead of circuit breakers
  • No safety switches on the board
  • Rust, cracks or water getting into the enclosure
  • A box mounted at a height that no longer meets current rules
Old meter box and switchboard mounted high under a porch ceiling beside the front door of a Botany home, with porcelain fuses still in place
The old setup in Botany: mounted high under the porch ceiling, right beside the front door, still running porcelain fuses.

Height is the one nobody thinks about. An older box can sit well above where the current rules put it, which is exactly what we found on the Botany job below.

The other trigger is new load. EV chargers, granny flats and other additions draw more than older setups were built for, so the board usually gets assessed before that work can go ahead. A smart meter install can bring the same thing to light.

If you’ve had a defect notice from the network provider, that’s a different situation with its own deadline. Our guide to electrical defect notices covers what to do about one.

Meter box upgrade vs replacement vs relocation

People use these three words to mean much the same thing. They’re different amounts of work, and the difference shows up in the quote.

A meter box replacement is the simplest version. The old enclosure comes off, a new one goes on in the same spot, and nothing behind it changes.

Upgrading goes further. The enclosure is replaced, and so is whatever’s behind it that no longer meets current standards, whether that’s the main switch, the mains cable, the earthing or the switchboard itself.

Then there’s relocation, where the whole setup moves somewhere else on the property. Usually that’s to get it away from a front door or an entry path, or to bring the height into line.

In practice most jobs end up being a mix of all three.

How much does a meter box upgrade cost in Sydney?

What you pay depends almost entirely on how much has to change.

A straightforward meter box replacement in the same spot starts at around $2,800. A full upgrade like the Botany job below, where the box moves, the mains are replaced and the switchboard is done at the same time, sits at the top end, from around $5,500. Both figures include GST and are starting points, not quotes.

That’s a wide spread, and there’s no getting around it: two houses on the same street can need completely different work. Both figures are starting points, not quotes. What moves the price:

  • Whether your power is single phase or three phase
  • How many poles the new switchboard needs
  • Whether the box can stay where it is, and if not, how far it has to move
  • Whether the mains cable, earthing or main protection device also need replacing

The only way to get a real number is a site visit and a written quote. We’ll look at what you have, explain what has to change, and give you a price before any work starts.

Why a meter box upgrade needs a Level 2 electrician

The meter, the service line, the main protection device and the earthing all sit on the supply side of your property, between the network and your installation. In NSW only an accredited Level 2 ASP is licensed to work on that side.

Level 2 electrician connecting the mains inside a newly installed galvanised meter box
Connecting the new mains inside the enclosure. This is the supply side, and it’s Level 2 work.

This is usually where people get stuck. You’ve got a sparky you already use and trust, and the obvious question is whether they can just sort it out.

A regular electrician can do plenty inside the property, including a lot of switchboard work. What they can’t do is disconnect and reconnect your supply, move or replace the meter, or touch the service line coming in from the street.

That’s why most meter box jobs are Level 2 from the start, even when the part you can see looks simple. Plenty of people find that out after they’ve already booked someone. Our guide to the difference between a Level 2 and a regular electrician goes into more detail.

In short: if the job touches the meter, the service line, the mains or the earthing, only an accredited Level 2 ASP can legally do it. Worth checking before you book anyone.

How long does it take, and will the power go off?

The power does go off. Supply-side work can’t be done live, so the meter and mains have to be disconnected while the job happens.

How long it takes depends on the scope. A straight swap in the same spot is a much shorter job than a relocation with new mains, new earthing and a new switchboard.

On the Botany job below, the power was off during our working hours on both days and back on each evening, so the family weren’t without it overnight.

All of it goes in the quote before work starts, so you can plan around it.

A recent meter box upgrade in Botany

Earlier this year we upgraded and relocated the meter box and switchboard on a home in Botany.

A.SAL Electrical van parked at a Botany home on the day of a meter box upgrade
Set up on site in Botany, with the new cable ready to run.

The owners were planning two things: an EV charger, and a new smart meter. Both meant the existing board needed to be assessed first to see what was required. They also wanted it moved away from the front door.

The old meter and switchboard were mounted high up under the porch ceiling, right beside the entry. The switchboard still had porcelain fuses, the cabling ran across the brickwork to reach it, and the whole arrangement sat well above the height the current rules allow.

We moved the meter and switchboard to the side of the house and brought them down to a compliant height. That meant a new galvanised steel enclosure, a new main protection device, and a new 16mm XLPE main service line run to it. We also installed a new earth rod and earthing system, because the old one didn’t meet current standards.

Level 2 electrician fixing a new galvanised steel meter enclosure to the side wall of a Botany home
The new galvanised enclosure going up on the side of the house, away from the front door.
New earth rod and earthing conductor installed at the base of a Botany home
The new earth rod and earthing conductor. The old earthing didn’t meet current standards.

While the board was being replaced, the porcelain fuses and old breakers came out and RCBO safety switches went in. Porcelain fuses don’t offer the protection a modern safety switch does.

Finished meter box with a new electricity meter and a switchboard fitted with RCBO safety switches
The finished board: new meter, and RCBO safety switches in place of the porcelain fuses.

The work took two days on site, after a quote visit a fortnight earlier. The power was off during working hours on both days and back on each evening. We set that out in the quote up front so there were no surprises.

Relocated galvanised meter box on the side of a Botany home with conduit running up the wall to the service connection
Closed up and finished, with the conduit running up to the service connection.

Everything here is Level 2 work. The meter, the service line and the earthing all sit on the supply side of the property, so a regular electrician isn’t licensed to touch them.

Need a meter box upgrade?

If you’re planning an EV charger, waiting on a smart meter, or you’ve looked at your board and found porcelain fuses where the safety switches should be, the first step is getting someone out to look at it properly.

We’re an accredited Level 2 ASP based in Botany, covering Sydney’s Eastern Suburbs, Inner West and Lower North Shore. You’re dealing directly with Adolfo from the first call through to final sign-off. He’ll look at what you have, explain what has to change and why, and give you a written quote before anything starts.

Call 0411 167 798 or get in touch to book a site visit.

Get a Free Electrical Quote in Sydney

Ready to Get Started?

No job too big, no question too small. We’re easy to reach and happy to help.

light globes background